API · ASME · DIN · EN 規格対応の産業用バルブ
Vノッチセグメントボールバルブ
Vノッチセグメントボールバルブは、V字ノッチを設けたセグメントボールを90°回転させ、回転中にノッチエッジがシートをせん断します。全通ボールでは詰まる繊維質・スラリー・高粘度流体に対して優れた制御と遮断性能を発揮します。範囲は3/4"～20"（DN20～DN300）、ASME Class 150～600（PN16～PN100）、ボディは炭素鋼・ステンレス鋼・合金鋼・デュプレックスステンレス鋼、メタルシートおよびソフトシートタイプ、PDLシリーズ空圧アクチュエータ、PCLシリーズシリンダまたはポジショナーソレノイド付き電動操作に対応します。ノッチにより特性付き流量特性（あるOEMファミリーでは近似的に等パーセント、他の資料ではほぼ線形—ノッチ形状とポート仕様による）が得られ、調整範囲は約100:1～300:1が公表されています。電空ポジショナー付きの制御型はスパンに対して約±1.5%の基本誤差、ヒステリシス1.5%、デッドバンド0.6%に収まります。締切クラスはANSI/FCI 70-2およびIEC 60534-4によるシート選定です。メタルシートはClass IV、ガラス繊維強化PTFEはClass VI、クリアランスシートは閉止時におよそ最大流量の5%を意図的に通過させます。繊維を切断し粒子を押し出すせん断エッジは摩耗点でもあります。特性の不適合な状態での長時間の中間開度絞りはシートを急速に摩耗させ、従来型ボールバルブの高差圧スロットリングは用途ではなく乱用と記録されています（砂を含む生産水配管では数時間で内部部品が破損）。経験則ではソフトシートの差圧に対する開度は約20bar、メタルシートで約60barまでに制限されます。選定時は実流量条件に対してキャビテーション、フラッシング、チョークフロー、騒音、エロージョンを評価し、空力騒音はIEC 534-8-3、液体の流体力学騒音はIEC 60534-8-4により予測します。立ち上げではベンチストローク試験（全ストローク、校正、デッドバンド、非対称応答）を行い、垂直または水平に据え付け、比例制御にはポジショナー、開閉切替には複式ソレノイド弁を空圧版と組み合わせます。選定は制御範囲に対するVポート角度、媒体に対するシートタイプ、トルクとフェイルセーフ用途に対するアクチュエータで決まります。
次のファミリーに属する： ボールバルブ ファミリー
最終更新： 2026-11
ファミリー仕様
| Nominal valve connection size | 3/4"~20"（DN20~DN300） |
|---|---|
| Pressure class / nominal rating designation | ASME CLASS 150~600 (PN16~PN100) |
| Valve body material | Carbon steel, Stainless steel, Alloy steel, Duplex stainless steel |
| Operation / closure mode | PDL series pneumatic actuator, PCL series cylinder actuator, Electric actuator |
| Service temperature range | up to 1000F (540C) |
| seal types | Metal sealing, Soft sealing |
| applications | Control and cut-off duty on fibrous, slurry-bearing or viscous media |
| equal percentage characteristic and rangeability | The V-shaped notch in the ball produces an inherent flow characteristic close to equal-percentage, and manufacturers publish adjustable ratios (rangeability) from about 100:1 up to 300:1 depending on the design, allowing fine control over a wide flow turndown range. |
| positioner control accuracy | With an electropneumatic positioner accepting a 4-20 mA signal, the modulating version is specified with a basic error within about ±1.5% of span, hysteresis within 1.5% and dead band within 0.6%, which sets the achievable control accuracy for actuator and accessory commissioning. |
| seat type vs shutoff class ansi fci 70 2 | Shutoff class is specified per ANSI/FCI 70-2 and depends on seat construction: flexible metal and rigid metal seats reach Class IV, a reinforced PTFE seat reaches Class VI, while a clearance seat allows about 5% of maximum flow even when closed. Seat choice therefore determines whether the valve gives tight shutoff or deliberately limited shutoff in modulating service. |
| characterized rotary vs isolation ball selection | A standard full-bore ball valve is generally unsuitable for modulating duty because most of its usable flow change occurs over a narrow band of travel; a characterized (V-ball/V-port) design should be selected when its published flow characteristic, pressure-drop capability and shutoff performance suit the process and quarter-turn operation is advantageous. |
| eccentric seat reduces torque raises differential | An eccentric ball/seat geometry makes the ball wedge against the seat ring only at closure and release quickly on opening; this reduces operating torque, raises the allowable differential pressure, and limits seat rubbing wear compared with a centered design. |
| hardfaced seat options for severe service | Sealing rings are offered in soft (reinforced PTFE-type) and metal-sealed versions to match different operating conditions, and the sealing surface can be hardfaced with a cobalt-chromium hardfacing alloy for harsher services; the ball surface is hardened, ground and polished for abrasion resistance. |
| cavitation flashing noise must be evaluated | Selection of a V-port ball control valve for modulating service must evaluate cavitation, flashing, choked gas flow, noise, erosion and rangeability against the actual flow cases, since these pressure-reduction mechanisms - not the valve name - determine whether the trim survives the duty. |
| shear and selfcleaning for fiber solids | At the moment of closure the V-shaped ball edge shears across the seat, cutting fibers and extruding particles out of the seat area; this shearing plus self-cleaning action is what makes the valve suitable for pulp, wastewater and other fiber- or particle-laden media, and prevents the valve from jamming. |
| seat wear from prolonged partopen throttling | Seat loading and trim geometry designed mainly for shutoff leave a valve vulnerable to wear during prolonged part-open operation; on a poorly matched characteristic the loop shows cycling, poor low-flow resolution and rapid movement around a narrow operating point, so control-trim suitability must be confirmed for continuous throttling. |
| throttling a standard ball valve is abuse | Using a conventional ball valve as a throttling valve under high differential pressure is described as abuse rather than proper duty: a Class 900 rising-stem ball valve in produced water with sand destroyed its internals and leaked externally to atmosphere after only hours of throttling, forcing a plant shutdown. |
| soft seat differential opening limit | A field rule of thumb holds that a soft-seated ball valve should not be cracked open against a differential higher than about 20 bar (and even that can be excessive if parked part-open for hours), while hard-faced metal/metal seats are limited to roughly 60 bar; exceeding these limits during pressure-equalizing operations damages seats. |
| commissioning bench check and stroke test | Before process commissioning the assembled valve and actuator should be bench-checked and stroke-tested: verify full travel, calibration, action, linkage and feedback/limit indications, stroke the command in both directions, and record any deadband, sticking or asymmetric response. |
| installation orientation flanged interfaces | The compact quarter-turn body can be installed vertically or horizontally, and the pneumatic V-type control version works with a valve positioner for proportional modulation or with a double solenoid valve and control box for on/off switching duty. |
| leakage classes ansi fci 70 2 iec 60534 4 | Control-valve seat leakage is classified by ANSI/FCI 70-2 and IEC 60534-4: Class IV allows 0.01% of rated capacity and is the usual metal-seated target, Class V allows 0.0005 ml/min per inch of port per psi differential, and Class VI (bubble-tight, 0.15-0.3 ml/min) is the soft-seat class relevant to V-port valves offered with both seat types. |
| aerodynamic noise prediction iec 534 8 3 | Aerodynamic noise from a throttling control valve is predicted with IEC 534-8-3, a five-step method that computes mechanical power at the vena contracta, converts it to noise power via acoustic efficiency factors, and propagates it through pipe-wall transmission losses to a standard observer 1 m downstream; it gives a common basis for comparing valves across vendors. |
| hydrodynamic noise iec 60534 8 4 | For liquid services where a V-port valve throttles with high pressure drop, hydrodynamic noise is covered by the companion standard IEC 60534-8-4, which many manufacturers embed in sizing software; the aerodynamic part 8-3 alone does not cover liquid noise. |
| flanged one piece vport design | one flanged V-port segment valve family is built as a one-piece body with integrally cast flanges, face-to-face per ISA 75.08.02 and IEC 60534-3-2 |
| flanged pressure class envelope | ASME Class 150 and 300 available 1"–32"; ASME Class 600 available 1"–4", PN 10 (DN 200–800), PN 16 (DN 100–800), PN 25 (DN 200–800), PN 40 (DN 25–600), JIS 10K/16K/20K flange drillings offered on the ASME 300 body casting (1"–28") |
| segment valve size envelope | sizes 1", 1-1/2", 2", 2-1/2", 3", 4", 6", 8", 10", 12", 14", 16", 20", 24", 28", 32" (DN 25 to DN 800), flanged end connections only |
| temp envelope by bearing seat build | temperature envelope steps with construction: -52 to +260 °C with soft bearings, -52 to +315 °C with metal bearings, and -52 to +425 °C with metal bearings plus high-temperature seats |
| shutoff class metal soft seat iec | shut-off classification per IEC 60534-4 / ANSI-FCI 70.2: metal seat Class IV with Class V optional under high differential test pressure and 10 x ISO 5208 Rate D; soft seat Class V with Class VI optional |
| inherent flow characteristic equal percentage | inherent flow characteristic of the flanged V-port segment design is equal percentage |
| fire safe certification api607 | fire-safe design certified to ISO 10497:2010 (API 607, seventh edition) |
| noise cavitation trim option | a dedicated low-noise / anti-cavitation trim reduces aerodynamic noise and prevents cavitation, offered for 2" (DN 50) and larger valves |
| reduced cv trim codes | reduced-Cv trims for the DN 25 / 1" valve limit maximum Cv to 0.5 (code C005), 1.5 (C015), 5.0 (C05) and 15.0 (C15) |
| metal seat construction temp | standard tight metal seat: 316 SS with cobalt-based hard facing seat, nickel-chromium alloy 625 spring, filled-PTFE lipseal / SS Elgiloy spring, rated -52 to +315 °C for general tight-shut-off service, sizes 1"–32" (DN 25–800) |
| soft seat construction temp | soft seat: 316 SS with PTFE + high-cycle filler in sizes 1"–6", 316 SS with PTFE + 25% carbon insert in sizes 8"–32", nickel-chromium alloy 625 spring, filled-PTFE lipseal back-up and PTFE seat seal, rated -52 to +260 °C for general tight shut-off |
| non tight metal seat erosive | non-tight metal seat in cobalt-based alloy rated -80 to +425 °C for extremely erosive applications, installed with reversed flow direction |
| high temp metal seat option | high-temperature metal seat option: 316 SS with cobalt-based hard facing (316 SS with chrome-carbide facing variant), nickel-chromium alloy 625 spring and FKM seat seal, rated -30 to +200 °C for general service |
| body seat test pressure basis | all valves undergo pressure testing at the factory: body shell test at 1.5 x the valve pressure rating |
| trim rotation direction | valve trim rotation is clockwise to close |
| segment material options severe service | segment material options include AISI 329 with hard facing, CG8M with hard facing or chrome-carbide facing, and titanium with ceramic coating or uncoated titanium |
| rotary emission bearing design | bearings are located inside the valve body giving larger bearing areas, lower bearing loads and longer bearing life, and rotary operation reduces fugitive emissions dramatically compared with a sliding-stem design |
| segmented design envelope asme | a segmented ball control valve series covers NPS 1 to 16 (DN 25 to 400), one-piece body per ASME B16.34, pressure classes ASME 150/300/600 and PN 10/16/25/40, temperature -50°F to 500°F (-46°C to 260°C), flanged and flangeless end connections |
| leakage class ansi fci by seat | leakage classification per seat type: resilient seat Class VI and metal seat Class IV, both per ANSI/FCI 70-2 and IEC 60534-4 |
| face to face flanged segment | face-to-face dimensions per ISA 75.08.02 and ASME B16.10 on flanged builds; flangeless version to the manufacturer internal standard; flange drilling per ASME B16.5 |
| rangeability port options 300to1 | 300:1 rangeability with equal-percentage inherent flow characteristic and three standard V-port options (standard profile, 60° and 30°), plus customized characterization on request |
| vport profiles throttling range | standard, 60-degree and 30-degree V-port profiles give the characterized throttling range; custom port geometry available on request |
| top flange iso actuation mount | top flange mounting per EN 1092-1 and ISO 5211 for actuator mounting |
| body seat stem material options | body ASTM A216 WCB carbon steel, seat options: reinforced PTFE (316L-grade), and metal seats with cobalt-alloy hard facing, chrome carbide, or solid tungsten carbide, stem options: 17-4 PH stainless steel, nitrogen-strengthened XM-19 stainless steel, SMO 254, and super duplex UNS 32760 |
| seat energization differential behavior | a seat spring provides constant force sealing the seat against the segment at low differential pressures; at higher differential pressures optimized seat loading takes over the seal function |
| splined stem connection control | splined stem-to-segment connection gives efficient torque transmission and precise control with low hysteresis and reduced deadband |
| pressure temp rating wcb class150 | ASME Class 150 WCB carbon-steel body pressure rating (psi at °F): 284 at -20–100°F falling through 200 at 305°F to 79 at 800°F |
| max shutoff differential size bands | maximum differential pressure for control vs shut-off duty is charted per ASME class and size band: Class 150 charts cover 1"–10" with a separate 12" band, Class 300 charts split 1"–3", 4" and 8", 10" and 12" bands (higher classes in the same bulletin) |
| cv metal seated table span | metal-seated Cv tables span 0.2 at 1" / 10% open up to 2,870 at the 16" valve (highest tabulated value, upper opening rows read positionally from the %Open grid) |
| seat temperature limits differential | FKM soft seats are limited to 420°F (216°C) in the differential-pressure charts, with special-material seats to 500°F (260°C) |
| initial opening table by seat | initial opening percentages with different seats on the flanged V-port segment builds (DN 25 to DN 700): metal seat S/A starts at 14.2% (DN 25 trim variants 10.3–11.9%) falling to 4.4% at DN 700; tight metal seat 1S starts 12.8% (9.3–11.4% mid-range) down to 5.9–6.3% at DN 500–700; soft seat T2 starts 24.1% (16.1–21.1%) down to 7.1% |
| ra re body rating temp split | body ratings: the internally-standardized (non-IEC face-to-face) execution per ASME Class 300 or PN 40; the IEC face-to-face execution per ASME Class 300 or PN 50/PN 40, with ASME Class 600 or PN 63/PN 100 optional in NPS 1"–4", face-to-face: the internally-standardized execution to the valve-maker internal standard, the IEC execution per IEC/EN 60534-3-2, operating temperatures: internally-standardized execution -40 to +260 °C; IEC execution -50 to +260 °C with soft bearings, -50 to +315 °C with metal bearings in sizes 2"–10", and -50 to +425 °C with metal bearings plus high-temperature seats in sizes 2"–10" |
| Shell pressure rating | up to 285-740 psi (1960-5100 kPa) |
| shutoff class | Per ANSI/FCI 70-2, Flexible Metal: Class IV, Rigid Metal: Class IV, Reinforced PTFE Seat: Class VI, Clearance Seat: 5% of max flow when closed |
| body styles | Flanged or flangeless |
| Actuator type / construction | Handwheel, Chainwheel, Double-acting and spring-return cylinder actuators, Spring-return diaphragm actuator |
範囲と出所の注記
| rangeability | Rangeability: one OEM states adjustable ratio 100:1 while another states up to 300:1 (spec table 250:1/300:1) - published rangeability differs by manufacturer and must not be generalized to a single number. |
|---|---|
| inherent flow characteristic | Inherent flow characteristic: OEM pages describe the V-notch as approximately equal-percentage while other engineering sources describe characterized V-ball designs as near-linear - the curve depends on notch geometry and port option, so quote as characterized per design rather than one shape. |
| soft seat shutoff | Soft-seat shutoff: an OEM page claims zero leakage for soft seals, but ANSI/FCI 70-2 Class VI still permits a small quantified leakage (0.15-0.3 ml/min per a control-valve reference) - the standardized leakage-class wording governs over marketing zero-leak claims. |
| size pressure envelope | Size/pressure envelope: the tenant entry 3/4-20 inch (DN20-DN300) Class 150-600 sits inside one OEM line listed at 1-20 inch Class 150 and 1-12 inch Class 300 - per-OEM envelopes differ and must not be merged into one claim without tenant confirmation. |
注文と書類
書類
お問い合わせの際に必要な書類セットをお知らせください——この型番仕様の典型的な項目（材質証明書、記載の検査規格に基づく試験報告書、寸法図）は、見積時に確認のうえ供給されます。
お見積り
見積可能なお問い合わせには次の事項をご記入ください：呼び径と圧力レーティング、ボディ・シート材質の希望、接続方式、操作方式、温度を含む使用流体。このページの典型値はベンチマーク参考範囲です。拘束力のある値は見積時に確定します。
サンプルと供給
供給条件、発注数量、納期は注文ごとに協議します——お問い合わせの際に納入国と希望スケジュールをお知らせください。
保管と輸送
バルブはシート・シールを紫外線、オゾン、変形から保護して保管し、据付まで端面保護カバーを取り付けたままにしてください。エラストマーまたは PTFE シートの仕様では、屋外での長期保管を避けてください——シート材料は直射日光と凍結条件で最も劣化が早くなります。
よくある質問
vノッチセグメントボールバルブの見積依頼には何を含めるべきですか？
適用規格とクラス、呼びサイズ、ボディおよびシート材、使用媒体と温度、納入先——欠落している項目は見積の過程で確認します。
vノッチセグメントボールバルブにはどのサイズと圧力等級がありますか？
このバルブの検証済みサイズと圧力等級範囲はまだ本ページに掲載されていません——お客様の使用条件に適したサイズと圧力等級は見積の過程でご提案し、確認します。使用条件を問い合わせに添えていただければ、選定結果を見積書に記載します。
vノッチセグメントボールバルブにはどのボディ材質がありますか？
このバルブの検証済みボディ材質範囲はまだ本ページに掲載されていません——お客様の使用条件に適したボディ材質は見積の過程でご提案し、確認します。使用条件を問い合わせに添えていただければ、選定結果を見積書に記載します。
Vノッチセグメントボールバルブ の見積依頼
こちらからご要望をご提出ください——見積に直結するお問い合わせには、適用規格とクラス、口径、材質、流体、温度、納入先をご記入ください.
お客様の情報の取り扱いについては、プライバシー通知をご覧ください。