API Β· ASME Β· DIN Β· EN standard industrial valves
Triple Duty Valves
Triple-duty valves fold three pump-discharge functions into one quarter-turn body - calibrated flow balancing, non-slam check, and positive shut-off - cutting mechanical-room space, installation labour and the extra flange joints of a three-valve manifold. The tenant band is DN65-DN300 in cast iron with straight and angle patterns and flanged, threaded or grooved ends; referenced executions run 1-1/2 to 16 in with ratings from 175 psi WOG on distributor-listed lines up to 375 psi / 300 F on the strongest reference, where drip-tight isolation is tested at 150 percent of rating and the body converts straight-to-angle on site. Balancing is set against a calibrated nameplate with a memory stop that restores the set position after shut-off; the soft-seat, spring-assisted disc damps chatter, and cam-action seating lets some executions seal tight on metal seats. The type is discharge-side specific: mount far enough from the pump to avoid check-assembly chatter, keep the stem/handle out of the downward position, and expect to close about 15 percent from full open for correct operation. The same device appears under several trade names across pump accessory lines; a triple-duty valve complements rather than replaces a dedicated balancing valve where flow-measurement accuracy is critical.
Part of the Check Valves family
Last updated: 2026-11
Family specifications
| size range | DN65 to DN300 |
|---|---|
| body materials | Cast Iron |
| body materials | Cast Iron, Bronze Seat |
| disc materials | A536 Nickel Plated Ductile Iron, Bronze B62 |
| seat materials | A536 Nickel Plated Ductile Iron, EPDM O-Ring |
| cover flange materials | Cast Iron |
| stem materials | SS410 |
| packing materials | Non-Asbestos |
| spring material | 300 Series Stainless Steel |
| function definition | A triple-duty valve replaces three valves with one body - shut-off, check and calibrated flow balancing - which is what removes the footprint of a three-valve pump-discharge manifold in the mechanical room. |
| closing mechanics | Closing is a two-stage quarter-turn action: the plug rotates to block the downstream port so pressure equalizes around the clapper, then the plug cams against the clapper backside for the final tight fit - the maker recommends turning to normal tight fit then bumping the plug lightly. |
| backflow protection range | Backflow protection holds across a wide range of system-balance settings because the check element is spring-assisted, not dependent on a single operating point. |
| size end envelope oem | The referenced OEM line spans 1-1/2 through 16 inch in flanged or threaded ends (globe style); the tenant band DN65-DN300 sits inside this envelope. |
| drip tight isolation test | Isolation quality is testable, not assumed: the referenced execution is designed and tested for drip-tight shut-off at 150 percent of maximum working pressure. |
| convertible body | Straight- versus angle-pattern is a site decision on convertible executions: the body can be changed in the field, replacing a separate 90-degree elbow on the pump discharge. |
| pressure temp envelope | The referenced execution is rated to 375 psi maximum working pressure and 300 F (150 C), sized 1-1/4 inch NPT through 12 inch flanged. |
| throttle design | Throttling uses a plug-and-disc design rather than a globe-style trim, which keeps the balance function and the shut-off seat on the same closure member. |
| dominant line envelope | Distributor listings for the dominant straight/angle-pattern line show cast iron bodies with flanged, NPT and grooved ends, all rated 175 psi WOG - a materially lower ceiling than the 375 psi reference execution. |
| calibrated balance memory | Balancing is calibrated against a nameplate scale so system flow can be set to a number, and the memory button returns the valve to its set position after shut-off. |
| anti chatter seat | The soft seat design damps valve chatter, protecting the trim from the noise and seat damage that chatter produces. |
| non slam staged parallel | The non-slam check element prevents backflow and gravity circulation in staged and parallel pumping, protecting the idle pump from reverse rotation. |
| cam seating metal seats | The disc approaches the seat with a cam action that produces high seating pressure, so tight shut-off is achievable even with metal seats and discs, not only soft seats. |
| memory stop function | Most triple-duty valves carry a pre-set balance and a memory stop so the balancing position can be restored exactly after shut-off; many models add calibrated markings, test ports and manufacturer performance data for field flow setting. |
| vs dedicated balancing valve | A triple-duty valve balances, but it is not a dedicated balancing valve: where flow-measurement accuracy or specialized balancing control is critical, the designer should verify whether the combined valve is appropriate or a dedicated balancing valve is preferred. |
| installation distance chatter | Placement matters: mounted too close to the pump discharge the check assembly chatters, wearing springs and the flapper prematurely and distorting gauge differential readings. |
| orientation limit | Orientation is restricted: vertical or horizontal mounting is acceptable, but the stem or handle must not point downward or upside down, and the valve cannot be left fully open - it must be closed about 15 percent to operate correctly. |
| naming map | The same device appears under different trade names across pump-accessory lines, so cross-line comparison should start from the shared three-function definition of shut-off plus check plus calibrated balancing. |
| maintainability | Routine maintenance is mainly leak checks at the packing nut and bonnet gasket; stem packing, disc and nameplate are replaceable internals on most executions. |
| bg catalog mwp | The straight-pattern catalog line is rated 175 PSIG (1,207 kPa) maximum working pressure. |
| bg cv table straight | Cv at 100% stem rise on the straight-pattern line spans 83-3,000 m3/h (flowmeter reference) and 77-3,225 m3/h (pressure-drop reference) across 2-14 in sizes. |
| bg cv 4in reference | A 4 in execution of the combined valve carries a pressure-drop Cv of 320 in catalog reference data. |
| bg commissioning dp | Gauge readings across the valve support commissioning: they indicate how to trim the pump impeller or set the maximum speed of the variable-frequency drive. |
| bg pt ports | Integrated pressure-temperature test ports allow direct measurement for flow verification. |
| bg ashrae balancing | Balancing practice reference: hydronic systems are proportionally balanced to minimize throttling losses first, then the pump impeller is trimmed or pump speed adjusted to meet design flow. |
| bg disc soft seat | One catalog execution pairs a brass disc with a soft seat to provide positive shut-off together with the non-slam check function. |
| peer model designation example | Flanged 2-1/2 in straight-pattern units are designated 3DS-2-1/2S under catalog number 132122. |
| peer spring disc check | The check element is an integrated spring-loaded disc; flow-optimized internal geometry limits pressure drop while preventing reverse flow and water hammer. |
| peer tsvn designation | The globe-style quarter-turn combined valve line from one maker carries designation TSVN, offered flanged or threaded in sizes 1-1/2 through 16 in. |
| max working pressure | 8 Bar |
| max operating temperature | 120C |
| disc material | Brass, EPDM Seal Insert |
| stem material | Stainless Steel |
| packing material | Teflon-Graphite, Asbestos-free |
| gasket material | Asbestos-free |
| readout valve | Brass, NPT insert, Check Valve |
Scope & source notes
| pressure envelope | Pressure envelope: the B&G distributor listings cap at 175 psi WOG while the Pentair Aurora 1040 reference reaches 375 psi / 300 F - the type has no single industry pressure ceiling; class follows the specific execution. |
|---|---|
| size envelope | Size envelope: tenant band DN65-DN300 (2.5-12 in) sits inside the Wheatley 1-1/2-16 in globe-style line but above the Pentair 1-1/4 in NPT low end - boundaries are execution-specific. |
| fully open prohibition | Fully-open prohibition: the Liberty guidance that the valve must be closed ~15% from full open to operate correctly is a balancing-function note, not a general check-valve rule - conflicts with how plain check valves are described elsewhere on the site. |
| seat material split | Seat material split: B&G listings emphasize soft (spring-assisted, anti-chatter) seats while the Liberty cam-action note supports metal-seat tight shut-off - both exist, but they are different execution choices, not one industry standard. |
Ordering & documentation
Documents
Ask for the documentation set with the inquiry β typical items (material certificates, test reports to the listed inspection standard, dimensional drawings) are confirmed and supplied with the quotation.
Quotation
Send the medium, temperature, pressure, size and connection for a quotation-ready inquiry. Lead time, MOQ and price are confirmed at quotation, together with the documents to be supplied with the order.
Sample & supply
Supply terms, order quantities and lead time are agreed per order β state the destination country and required schedule with the inquiry.
Storage & shipping
Store valves with seats and seals protected from UV, ozone and deformation, and keep end-face protectors on until installation; storage limits and shipping arrangements for the selected materials are confirmed at quotation.
Frequently asked questions
What sizes and pressure ratings are available for triple duty valves?
The published size range is DN65 to DN300. Availability of a specific size and rating is confirmed at quotation.
What materials are triple duty valves available in?
The published specification lists body materials: Cast Iron. Material availability for a specific size and rating is confirmed at quotation.
What should a quotation inquiry for triple duty valves include?
The governing standard and class, nominal size, body and seat materials, the service medium with temperature, and the destination β anything missing is confirmed during quotation.
Request a quote for triple duty valves
Submit the requirement here β a quotation-ready inquiry states the governing standard and class, size, materials, medium, temperature and destination.
What happens to your details is described in our privacy notice.
Get a quotation for Triple Duty Valves
Send the standard, pressure class and size for a quotation-ready inquiry β answered with documents and terms.